Security Link SL150 Guide de dépannage Page 115
- Page / 144
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
23–1
SECTION 23
System Operation
••••••••••••••••••••••••••••••••••••••••••••••••••
In This Section
♦
Security Codes
♦
Keypad Functions
♦
Relay/Powerline Carrier Devices
♦
4285/4286 VIP Module
♦
Exit Error Alarm Displays
♦
Trouble Conditions
••••••••••••••••••••••••••••••••••••••••••••••••••
Security Codes
Installer Code
The installer programs the 4-digit Installer code initially as part of the programming
procedure. The factory default Installer code is 4-1-1-2, but may be changed in field
✱
20.
The Installer code is the only code that can enter Programming mode. In normal operation
mode, it is also used to enter the Master code, which allows access to the normal functions of
the system.
Master Code
In normal operation mode,
the Installer code is used to enter the 4-digit Master security
code using
the hardwired connected keypad.
Therefore:
To enter the system's Master code, enter:
[Installer code]
+
8
+
02
+
[desired 4-digit Master code]
To change the Master code, enter:
[Master code]
+
8
+
02
+
[new Master code]
+
[new Master code again]
Secondary User Codes
In Normal Operation mode, the Master security code can be used to assign up to 14
secondary user 4-digit security codes. The Master code is also used to remove any secondary
User code(s) from the system (individually). During assignment of user codes, a user can also
be assigned to a macro, as indicated below.
To assign (or change) a user code
, enter the following on the keypad:
[Master code]
+
CODE
key
+
User
# [03–16]
+
[desired User Code]
The folowing screen will appear, accompanied by three beeps from the keypad.
*
Execute Macro ?
0 = No 1 or 2
*
This display will not appear if using a fixed-word keypad – only beeps will be heard.
If a user is going to be assigned to a macro, enter 1 or 2. You may assign a user to either of
the two macros. If not assigning a user to a macro, enter “0”.
Note: Programming a macro for a user will be found in Section 20 – Macros (Speedkey).
The system will emit a single beep when each user code has been successfully entered.
To delete a user security code
,
enter the following on the keypad
:
[Master code]
+
[CODE] key
+
User No. (03–16)
- 6HF XULW\6\VWHP 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- FINAL POWER 12
- Installing the Control 13
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Installing the Backup Battery 18
- Earth Ground Connections 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–8 23
- Remote Keyswitch (Zone 7) 27
- Wired Zone Expansion 33
- Wireless Expansion 37
- 1 2 3 4 5 38
- Installing the 5800TM Module 39
- Jam Detection and Reporting 39
- Appendix A 42
- Powerline Carrier Devices 47
- Programming Relay Outputs 48
- 4285 & 4286 VIP Module 49
- Section 11: 50
- Audio Alarm 50
- Verification (AAV) Unit 50
- 4285/4286 51
- VIP MODULE 51
- External Sounders 53
- Sounder Connections and Power 54
- Sounder Supervision 54
- Testing the Sounder 54
- Long Range Radio 55
- Dynamic Signaling Feature 56
- 4285 or 4286 58
- Final Power-Up 59
- Battery Tests 60
- Mechanics of Programming 61
- Loading Factory Defaults 63
- Exiting the Programming Mode 63
- Data Field Descriptions 69
- OUTPUT TO LONG RANGE RADIO 74
- Allows 81
- Zone Programming 83
- 86
- To Remove a Zone 88
- Section 16 -Zone Programming 91
- Output Device Programming 93
- Zone Lists 99
- Alpha Descriptor Programming 101
- Adding Custom Words 103
- ALPHA VOCABULARY LIST 105
- CHARACTER (ASCII) CHART 105
- Macros (SpeedKey) 107
- Remote Programming and 109
- Control (Downloading) 109
- Remote Programming Commands 110
- Initial Download 110
- System Communication 111
- System Operation 115
- Keypad Functions 116
- Testing the System 121
- Troubleshooting Guide 123
- POSSIBLE CAUSE REMEDY 124
- SYMPTOM POSSIBLE 124
- CAUSE REMEDY 124
- CONTACTING TECHNICAL SUPPORT 125
- In This Section 127
- APPENDIX A 131
- Regulatory Agency Statements 133
- Warnings and Limitations 135
- DOC LOAD NO.: 3 143
- ¬19'l 144
- Two Mid America Plaza 144
- Suite 200 144
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Security Link SL150
(29 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels